Menu
Home
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Reply to thread
Click here to become an Official Member of BMW Club Malaysia
Download Form
Home
Forums
The BMW Range
5 Series
E60, E61
E60 jerk..
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="E60MSport" data-source="post: 396662" data-attributes="member: 3686"><p>Please correct me if I'm wrong. It could be the dreaded Transmission Slam. I am also experiencing the same problem and have sent my vehicle for a transmission adaptation whereby he previous learning data will be cleared and readapted. I will only have the car back with me later on. Fingers crossed.</p><p></p><p>Sourced this of another website.</p><p></p><p>The following software errors were corrected with the release of CIP 17.01(Target data Status E060-05-06-500).</p><p></p><p>Vehicles equipped with 6HP26 up to 4/05, customer complains of harsh downshift. Refer to SI B24 03 05.</p><p></p><p>Here is the SIB240305 bulletin:</p><p></p><p>SUBJECT</p><p>Harsh 2-1 Downshift</p><p></p><p></p><p>MODEL</p><p>E60 (545i); E63/64 645(Ci/Cic) with 6HP26 up to 04/05</p><p></p><p></p><p>SITUATION</p><p>Customer may complain of the following:</p><p></p><p>An excessively harsh 2-1 downshift when decelerating to a stop, or</p><p></p><p>Transmission "bangs" into gear when accelerating from a full or a "rolling" stop (vehicle did not come to a complete stop).</p><p></p><p>CAUSE</p><p>EGS software.</p><p></p><p>CORRECTION</p><p>On a customer complaint basis only, reprogram/recode complete vehicle using SSS with CIP on-line update 17.01, or higher.</p><p></p><p>Important:</p><p></p><p>Transmission temperature must remain below 50 deg C and trans shifter must be placed in P position prior to the start of CIP programming.</p><p></p><p>WARRANTY INFORMATION</p><p>Covered under the terms of the BMW New Vehicle Limited Warranty.</p><p></p><p>For the appropriate defect code and labor operation refer to the KSD system.</p></blockquote><p></p>
[QUOTE="E60MSport, post: 396662, member: 3686"] Please correct me if I'm wrong. It could be the dreaded Transmission Slam. I am also experiencing the same problem and have sent my vehicle for a transmission adaptation whereby he previous learning data will be cleared and readapted. I will only have the car back with me later on. Fingers crossed. Sourced this of another website. The following software errors were corrected with the release of CIP 17.01(Target data Status E060-05-06-500). Vehicles equipped with 6HP26 up to 4/05, customer complains of harsh downshift. Refer to SI B24 03 05. Here is the SIB240305 bulletin: SUBJECT Harsh 2-1 Downshift MODEL E60 (545i); E63/64 645(Ci/Cic) with 6HP26 up to 04/05 SITUATION Customer may complain of the following: An excessively harsh 2-1 downshift when decelerating to a stop, or Transmission "bangs" into gear when accelerating from a full or a "rolling" stop (vehicle did not come to a complete stop). CAUSE EGS software. CORRECTION On a customer complaint basis only, reprogram/recode complete vehicle using SSS with CIP on-line update 17.01, or higher. Important: Transmission temperature must remain below 50 deg C and trans shifter must be placed in P position prior to the start of CIP programming. WARRANTY INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty. For the appropriate defect code and labor operation refer to the KSD system. [/QUOTE]
Verification
Post reply
Home
Forums
The BMW Range
5 Series
E60, E61
E60 jerk..
Top
Bottom
